Toyota Automobile Parts 712578 User Manual

ADVANCE ADAPTERS INC. P/N: 712578  
P.O. Box 247, 4320 Aerotech Center Way  
Paso Robles, CA 93447  
PAGE 1 OF 3  
Telephone: (800) 350-2223  
Fax: (805) 238-4201  
Page Rev. Date: 04-07-00  
TOYOTA L/C 6 CYLINDER ENGINE  
USING THE NV4500 5 SPEED TRANSMISSION  
KIT CONSISTS OF:  
NOTE:  
No.  
Qty Part No.  
Description  
This adapter is not compatible  
with 1996 or newer NV4500  
transmissions. Special adapters  
are available for 1996 or newer  
transmissions.  
1.  
2.  
3.  
4.  
5.  
1
1
2
1
1
712577-BLK  
712578-BLK  
716123  
716139  
716157  
NEWBELLHOUSINGFORGMENGINExNV4500  
LARGESTEELADAPTERPLATE  
DOWEL PINS (Pressed in steel plate)  
CLUTCHFORKWEDGE  
PILOTBEARINGSLEEVE  
(Modified to 1/4" shorter before shipping)  
CLUTCHRELEASEARM  
BALL PIVOT STUD (Installed in bellhousing)  
SLAVECYLINDERBRACKET  
BEARINGCOLLAR&BEARINGASSEMBLY  
3/8"LOCKWASHERS  
H.H.C.S.3/8"-16x1"LONG  
H.H.C.S.3/8"-16x1-1/4"LONG  
3/8" WASHERS  
NEWVENTUREINSTRUCTIONMANUAL  
LANDCRUISERINSTRUCTIONMANUAL  
6.  
7.  
8.  
9.  
10.  
11.  
12.  
13.  
14.  
15.  
1
1
1
1
8
2
6
4
1
1
716176  
716180  
716288  
716316  
723704  
723721  
723722  
723735  
NV001  
TLC001  
STEP-BY-STEP INSTALLATION PROCEDURES:  
1. Secure the vehicle in a position that will prevent any movement from the tires rolling back and forth.  
2. Remove the stock skid plate.  
3. Remove both front and rear drive shafts.  
4. Remove existing exhaust system with the exhaust manifold remaining in position.  
5. Disconnect and remove both the transmission and transfer case shifter assemblies.  
6. Disconnect the battery.  
7. Disconnect both the emergency brake and speedometer cables.  
8. Disconnect the back up switch wires from the existing transmission.  
9. Remove the transmission and transfer case assembly from the vehicle.  
10. Remove the stock 6 cylinder starter motor assembly.  
11. Remove the rear factory tubular crossmember support. This will require a torch and you should make sure that all fuel lines  
and brake lines have sufficient clearance.  
12. Disconnect the slave cylinder from the bellhousing.  
13. Support the rear of the engine with a small floor jack.  
14. Remove the Toyota bellhousing from the back of the engine.  
15. Unbolt the pressure plate assembly from the flywheel.  
16. Disconnect the bellhousing mounts from the frame to allow clearance for the new bellhousing assembly.  
17. Remove the flywheel assembly and have it machined if necessary.  
18. Inspect the Toyota rear main seal and take appropriate measures.  
19. Remove the Toyota pilot bearing from the back of the engine crank.  
20. Install the new pilot bushing supplied with the adapter kit.  
21. On the original Toyota bellhousing, you will need to remove the timing pin located on the front side of the bellhousing. The pin  
must be reinstalled into the Advance Adapter plate in the center of the square opening. Use a hand held drill motor to position  
the hole for installation of the original Toyota pin.  
SPECIAL NOTE:  
The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the components  
will void any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion, we strongly  
recommend that you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance Adapter components.  
We recommend that a service manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment. These manuals are  
normally available at automotive dealerships and parts stores.  
 
ADVANCE ADAPTERS INC. P/N: 712578  
P.O. Box 247, 4320 Aerotech Center Way  
Paso Robles, CA 93447  
PAGE 3 OF 3  
Telephone: (800) 350-2223  
Fax: (805) 238-4201  
Page Rev. Date: 08-15-95  
TOYOTA L/C 6 CYLINDER ENGINE  
USING THE NV4500 5 SPEED TRANSMISSION  
NOTES:  
1. Theoriginalbellhousingmountsareremovedfromframetoallowfornewbellhousing  
clearance.  
2. A new rear mount on the back side of transfer case #716022-TSW will be required on FJ40.  
FJ40 with split T/C 19 spline and FJ60 will need new crossmember under adapter.  
3. LongerspeedometercableandemergencybrakecablesareavailablefromB.T.B. Products.  
4. To maximize clutch engagement, slave cylinder works best when installed to inner slot.  
SPECIAL NOTE:  
The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the components will void  
any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion, we strongly recommend that  
youcontactoursalesdepartmentformoreinformation.ThisinstructionsheetisonlytobeusedfortheassemblyofAdvanceAdaptercomponents.Werecommendthataservicemanual  
pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment. These manuals are normally available at automotive dealerships and  
parts stores.  
 

Tektronix Sander TDS 600C TDS 700D User Manual
Tektronix Sander TDS5000B Series User Manual
Texas Instruments Network Router CC2530ZNP User Manual
Timex Heart Rate Monitor 117 095000 User Manual
Tripp Lite Surge Protector ISOBAR825ULTRA User Manual
Tyco Electronics Car Video System 2242L User Manual
Ultra Start Automobile Alarm 1250 User Manual
Video Products Computer Hardware USB SUN User Manual
ViewSonic Computer Monitor VA703M User Manual
ViewSonic Projector PJ551D User Manual