Toyota Automobile Accessories TY 71 00 G3 User Manual

Page 1 of 3  
TOYOTA TUNDRA 2000-2006  
TOYOTA SEQUOIA 2001-2007  
(MANUAL CLIMATE CONTROL ONLY)  
See page 2 for Automatic Climate Control  
PART NUMBER: TY-71-00-G3  
PLEASE READ COMPLETE INSTRUCTIONS BEFORE INSTALLING THIS VSM G3  
All instructions assume a drivers seat vantage point. Caution is advised when removing and reassembling  
wood or plastic parts of a dash. Applying unnecessary force or pressure may cause a piece to crack or break.  
When properly installed, the metal between the ball and 2 small holes is all that is exposed.  
(Some exceptions apply).  
#2 Phillips screwdriver, hook tools, 5/64” drill bit and drill, marking pen.  
VSM G3, A Plate, J Stem, two (2) #8 1/2” screws  
Right of air vent  
TOOLS REQUIRED:  
PARTS INCLUDED:  
LOCATION:  
STEP 1. Locate the two air vents that are on the right and left  
sides of the radio. Remove both of these air vents by inserting  
the hook tool between the vents and the bezel and carefully  
prying outward on the vents to remove. Set the vents aside.  
Inside the vent cavities locate and remove two (2) Phillips  
screws using the Phillips screwdriver. Set the screws aside.  
STEP 2. Locate the three knobs that are on the climate  
control. Grasp the knobs and carefully pull toward you to  
remove. Set the knobs aside. Locate and remove the three(3)  
Phillips screws that are behind the knobs. Set the screws  
aside. Grasp the top middle section of the bezel just above  
the radio and carefully pull towards you releasing the top clip.  
Insert both your hands into the air vent cavities. Grasp the  
bezel and pull toward you to release a series of six clips that  
are behind and attached to the back of the climate control.  
These clips hold the lower section of the bezel in place. When  
the bezel is loose do not disconnect any wiring. Let the bezel  
hang.  
1
STEP 3. Locate the flat section of plastic to the right of the  
right air vent. Place the VSM G3 over this section of plastic,  
making sure that the bottom of the G3 is level. Once the G3 is  
in position, mark two (2) spots for drilling pilot holes using the  
two (2) holes in the G3 as a guide. Set the mount aside.  
Carefully drill two (2) pilot holes using the 5/64” drill bit and  
drill, making sure to not drill too deep. Place the VSM G3 over  
the two pilot holes. Insert the two (2) #8 x 1/2” provided  
screws and tighten.  
2
STEP 4. Re-assemble the dash in reverse order. This completes  
the installation of your VSM G3.  
Note: See the Assembly Instructions for G3 Components for  
additional information.  
3
Pro.Fit International, Inc.® may not be held liable for any damage to a vehicle before, during or after the installation or removal of this VSM  
G3. Pro.Fit International may not be held liable for any personal injury resulting from accident or improper installation. Pro.Fit International,  
Inc.® 1335 Eagandale Court, Eagan, MN 55121, Ph: 651.688.3588 or 800.388.0073 Fx: 651.688.9876  
View Instruction & Updates  
Online at  
www.pro-fit-intl.com  
© Pro.Fit International, Eagan, MN 2008  
 
Page 3 of 3  
Mercury Mountaineer 2006-2008  
Ford Explorer 2006-2009  
Ford Sport Trac 2008  
TY-71-00-G3  
PLEASE READ COMPLETE INSTRUCTIONS BEFORE INSTALLING THIS VSM G3  
All instructions assume a drivers seat vantage point. Caution is advised when removing and reassembling  
wood or plastic parts of a dash. Applying unnecessary force or pressure may cause a piece to crack or break.  
When properly installed, the metal between the ball and 2 small holes is all that is exposed.  
(Some exceptions apply).  
TOOLS REQUIRED: #2 Phillips screwdriver, Dash Trim Tool (DTRT) 5/64” drill bit and drill, 7mm socket and driver  
marking pen.  
PARTS INCLUDED: VSM G3, A Plate, J Stem, two (2) #8 1/2” screws  
LOCATION: Right of Radio  
STEP 1. Apply parking brake and place gear shift into drive. Open  
center arm rest and remove two (2) 7mm bolts from the front of the  
console. Photo #1. Insert DTRT behind the gear shift trim bezel.  
Press down to release a retainer clip. Work the tool around the trim  
until all clips are released. Lift ring over gear shift and set aside.  
7mm  
STEP 2. Insert the DTRT behind the cup holder/shifter bezel near  
the 7mm bolt holes. Press down to release a clip. Work the tool  
around the bezel until all clips are free. Lift bezel over shifter,  
disconnect wiring and set bezel aside. Photo #1.  
1
STEP 3. Insert DTRT behind the upper-right corner of the radio  
bezel. Press down gently to release a clip. Work the tool around  
the bezel until it is completely free. Very carefully disconnect the  
wiring and vacuum lines from the bezel. Set bezel aside.  
STEP 4. Remove four (4) screws from the corners of the radio. Pull  
radio out of its cavity, wrap protective cloth around radio and let it  
hang down. DO NOT disconnect radio wiring.  
STEP 5. Place the VSM G3 against the right side of the radio cavity,  
aligning it just above the clip hole. Photo #2. Using the VSM G3 as a  
guide, mark the location of the two (2) screw holes and set the VSM  
G3 aside. Use a utility knife and trim the small ridge behind the VSM  
G3 so it sits tight against the dash pad. Drill two (2) pilot holes at  
the marked locations using a 5/64” bit and drill. Align the VSM G3  
over the pilot holes, insert two (2) #8 x 1/2” screws and tighten.  
Clip  
Hole  
2
STEP 6. Assemble the dash in reverse order, remembering to  
reconnect the wiring harness. You have successfully installed your  
VSM G3.  
Note: See the Assembly Instructions for G3 Components for  
additional information.  
3
Pro.Fit International, Inc.® may not be held liable for any damage to a vehicle before, during or after the installation or removal of this VSM  
G3. Pro.Fit International may not be held liable for any personal injury resulting from accident or improper installation. Pro.Fit International,  
Inc.® 1335 Eagandale Court, Eagan, MN 55121, Ph: 651.688.3588 or 800.388.0073 Fx: 651.688.9876  
View Instruction & Updates  
Online at  
www.pro-fit-intl.com  
© Pro.Fit International, Eagan, MN 2008  
 

Tech Craft TV Video Accessories BCE60 User Manual
Teledyne Carbon Monoxide Alarm gfc 7000ta User Manual
The Singing Machine Karaoke Machine STVG 502 User Manual
Toshiba Barcode Reader B 411 SERIES User Manual
Toshiba Network Card F Series User Manual
Toshiba Projection Television TLP S40 SVGA User Manual
Transition Networks Network Cables BFFG1XXX 1XX User Manual
Transition Networks Switch SISGM1040 162D User Manual
Viking Food Warmer RDEWD103 User Manual
Weed Eater Blower 530088127 User Manual